Autonomous prod bring-up, operator away. Three changes that together clear the last
blockers before `flux bootstrap`.
=== 1. TEMPORARY BOOTSTRAP GITEA — the last hard blocker, cleared ===
clusters/prod's source URL could not work: Gitea runs ON the dev cluster (the one slated for
decommission) and split-horizon DNS resolves gitea.home.keithjackson.dev to PROD's OWN
gateway. Stood up the existing bootstrap/gitea/bootstrap-gitea.sh on the operator's
workstation with HOST_NAT_IP=192.168.2.132; all three prod nodes verified reachable
(Gitea 1.22.6 via the API), no firewall change needed — prod is on the same /24, no NAT.
clusters/prod now points at http://192.168.2.132:3000/... under a boxed TEMPORARY banner
with a 5-step cutover checklist ending 'delete this whole block — dev's stanza is what done
looks like'. Repo verified PUBLIC with anonymous read two independent ways (API
"private":false; git ls-remote unauthenticated with GIT_TERMINAL_PROMPT=0), so NO secretRef
is needed — documented so a future auth failure is not misread as a network fault.
bootstrap-gitea.sh's header corrected: it documented HOST_NAT_IP=10.73.0.1, the RETIRED
libvirt NAT, and forbade agent use; the operator has now directed this for prod.
=== 2. WIRELESS DISABLED ON PROD (operator-reported) ===
k3s-prod-3 was on ethernet AND wireless, and the wifi DHCP client was overwriting
/etc/resolv.conf. Root cause of the silence: node_baseline's DNS `contended` detection
checked resolvconf and NetworkManager but NOT dhcpcd, so the role wrote resolvers, reported
success, and dhcpcd reverted them on lease renewal — the exact 'green run that fixed
nothing' the contended branch exists to prevent.
Now IaC, not a one-off: survey wireless hardware, **REFUSE to disable it if the path to the
node runs over the wireless interface** (the guard that meant an agent dying mid-apply cost
nothing), blacklist the driver so it never reloads, stop dhcpcd only where it holds a
wireless interface and nothing else, take links down and unload modules with NO reboot, then
report the resulting state. dhcpcd is now in the contended set without weakening fail-closed.
Applied and verified: node 3's wlp1s0 is GONE from /sys/class/net, dhcpcd inactive and its
unit not-found, ONE default route per node, all three on 8.8.8.8/1.1.1.1 resolving public
names. Safe and idempotent on nodes 1 and 2, whose wifi hardware was already down.
=== 3. flux_bootstrap PATH PARAMETERISED ===
bootstrap/flux/bootstrap.sh already read FLUX_ENV_PATH but the role never exported it, so it
ALWAYS bootstrapped clusters/dev — prod was impossible. Two behaviour-bearing lines: role
default clusters/dev + `environment: FLUX_ENV_PATH`, overridden to clusters/prod in
group_vars/k3s_prod. Proven per host with a read-only Ansible probe: prod hosts resolve
clusters/prod, localhost/hypervisor resolves clusters/dev. Only two definitions repo-wide.
DEV PROVEN BYTE-IDENTICAL for the source change: all 12 substituting Flux paths rendered for
both trees, 27/27 SHA-256 artefacts identical, with TWO POSITIVE CONTROLS (an overlay-level
canary and a deep-path content canary) confirming the harness detects change — and both
canaries proven restored. Honest scope note recorded: kustomize strips comments, so the
harness proves the built stream, not source comments.
L0 substitution check: 106 assertions, 0 hazards. ci/l0.sh and ci/lint.sh exit 0.
=== STILL BLOCKING A FULL PROD RECONCILE (operator decisions) ===
- S3_BACKUP_ENDPOINT remains TBD-PROD-*: prod CANNOT reach dev's versitygw at
192.168.1.9:9000 (verified UNREACHABLE from all three — the pfSense boundary), and a prod
backup target is a deferred operator decision. Deliberately NOT invented: a DR target on a
workstation container would create false confidence. Velero/CNPG backups will fail loudly.
- Prod's public resolvers mean the API server's oidc-issuer-url resolves PUBLICLY, so kubectl
SSO will not work on prod until split-horizon is solved for it (§4).
- The temp Gitea is a single container on the operator's workstation — a single point of
failure for prod reconciliation, acceptable for bring-up only.
Serves: R-GITOPS-01, R-DNS-01, R-DNS-03, R-ENV-02, R-ENV-03. Task: T-7.1.
Co-Authored-By: Claude Opus 5 (1M context) <[email protected]>
Per operator: the firewalld rule (VM->host:3000 for the Flux<-Gitea source) must be
IaC, not a manual command (R-ENV-01, R-PLAT-04).
- infra/ansible/playbooks/host-prereqs.yml: idempotent firewalld open on the libvirt
zone (localhost play, become; no extra collection).
- bootstrap/gitea/bootstrap-gitea.sh: now fully automates admin + public repo + push
(was manual instructions) — idempotent; creds stay 0600 on host, never committed.
Applying host-prereqs still needs host sudo (I lack non-interactive sudo); with
passwordless become a destroy/rebuild is fully unattended.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
Run a single Gitea container on the host (bootstrap/gitea/), outside the cluster,
while the cluster is built; Flux pulls this repo from it over the k3s-dev NAT
gateway (http://10.73.0.1:3000/Home-Network/home-network-k3s-impl.git, public repo
=> no creds, NAT-only). Wired the flux-system GitRepository url in clusters/dev.
Migrates to in-cluster Gitea in Phase 6. Pins confirmed. Author-only; gate PASS.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
jakman85andClaude Opus 5