jakman85andClaude Opus 5
9b8979a427
Autonomous prod bring-up, operator away. Three changes that together clear the last blockers before `flux bootstrap`. === 1. TEMPORARY BOOTSTRAP GITEA — the last hard blocker, cleared === clusters/prod's source URL could not work: Gitea runs ON the dev cluster (the one slated for decommission) and split-horizon DNS resolves gitea.home.keithjackson.dev to PROD's OWN gateway. Stood up the existing bootstrap/gitea/bootstrap-gitea.sh on the operator's workstation with HOST_NAT_IP=192.168.2.132; all three prod nodes verified reachable (Gitea 1.22.6 via the API), no firewall change needed — prod is on the same /24, no NAT. clusters/prod now points at http://192.168.2.132:3000/... under a boxed TEMPORARY banner with a 5-step cutover checklist ending 'delete this whole block — dev's stanza is what done looks like'. Repo verified PUBLIC with anonymous read two independent ways (API "private":false; git ls-remote unauthenticated with GIT_TERMINAL_PROMPT=0), so NO secretRef is needed — documented so a future auth failure is not misread as a network fault. bootstrap-gitea.sh's header corrected: it documented HOST_NAT_IP=10.73.0.1, the RETIRED libvirt NAT, and forbade agent use; the operator has now directed this for prod. === 2. WIRELESS DISABLED ON PROD (operator-reported) === k3s-prod-3 was on ethernet AND wireless, and the wifi DHCP client was overwriting /etc/resolv.conf. Root cause of the silence: node_baseline's DNS `contended` detection checked resolvconf and NetworkManager but NOT dhcpcd, so the role wrote resolvers, reported success, and dhcpcd reverted them on lease renewal — the exact 'green run that fixed nothing' the contended branch exists to prevent. Now IaC, not a one-off: survey wireless hardware, **REFUSE to disable it if the path to the node runs over the wireless interface** (the guard that meant an agent dying mid-apply cost nothing), blacklist the driver so it never reloads, stop dhcpcd only where it holds a wireless interface and nothing else, take links down and unload modules with NO reboot, then report the resulting state. dhcpcd is now in the contended set without weakening fail-closed. Applied and verified: node 3's wlp1s0 is GONE from /sys/class/net, dhcpcd inactive and its unit not-found, ONE default route per node, all three on 8.8.8.8/1.1.1.1 resolving public names. Safe and idempotent on nodes 1 and 2, whose wifi hardware was already down. === 3. flux_bootstrap PATH PARAMETERISED === bootstrap/flux/bootstrap.sh already read FLUX_ENV_PATH but the role never exported it, so it ALWAYS bootstrapped clusters/dev — prod was impossible. Two behaviour-bearing lines: role default clusters/dev + `environment: FLUX_ENV_PATH`, overridden to clusters/prod in group_vars/k3s_prod. Proven per host with a read-only Ansible probe: prod hosts resolve clusters/prod, localhost/hypervisor resolves clusters/dev. Only two definitions repo-wide. DEV PROVEN BYTE-IDENTICAL for the source change: all 12 substituting Flux paths rendered for both trees, 27/27 SHA-256 artefacts identical, with TWO POSITIVE CONTROLS (an overlay-level canary and a deep-path content canary) confirming the harness detects change — and both canaries proven restored. Honest scope note recorded: kustomize strips comments, so the harness proves the built stream, not source comments. L0 substitution check: 106 assertions, 0 hazards. ci/l0.sh and ci/lint.sh exit 0. === STILL BLOCKING A FULL PROD RECONCILE (operator decisions) === - S3_BACKUP_ENDPOINT remains TBD-PROD-*: prod CANNOT reach dev's versitygw at 192.168.1.9:9000 (verified UNREACHABLE from all three — the pfSense boundary), and a prod backup target is a deferred operator decision. Deliberately NOT invented: a DR target on a workstation container would create false confidence. Velero/CNPG backups will fail loudly. - Prod's public resolvers mean the API server's oidc-issuer-url resolves PUBLICLY, so kubectl SSO will not work on prod until split-horizon is solved for it (§4). - The temp Gitea is a single container on the operator's workstation — a single point of failure for prod reconciliation, acceptable for bring-up only. Serves: R-GITOPS-01, R-DNS-01, R-DNS-03, R-ENV-02, R-ENV-03. Task: T-7.1. Co-Authored-By: Claude Opus 5 (1M context) <[email protected]>
infra/ — node provisioning and the toolchain
OpenTofu (Proxmox VE) + cloud-init + Ansible bring up the 3-node k3s/Cilium dev cluster.
Spec: ../home-network-k3s/docs/02-environments-and-provisioning.md.
| Path | What |
|---|---|
tofu/ |
The "Create" stage: 3 cloud-init'd VMs on the Proxmox box (bpg/proxmox provider) |
cloud-init/ |
First-boot baseline shipped as a Proxmox user-data snippet |
ansible/ |
The "Baseline"/"Configure" stages: k3s HA, Cilium, kube-vip, the VPN egress gateway |
devcontainer/ |
The pinned toolchain (tofu, ansible, sops, age, flux, kubectl, helm and the whole CI gate toolchain) |
cluster.sh |
RETIRED — drove the old libvirt VMs; does not work against Proxmox |
PHASE1-STATUS.md |
Current state of the cluster and how to reconnect to it |
PHASE1-SCOPE.md |
Historical Phase-1 scoping doc (libvirt era — superseded) |
Where the cluster actually lives
The dev cluster is not on this workstation. It runs on a Proxmox VE host; the nodes sit on the Proxmox LAN and are reached across a pfSense NAT:
| Nodes | k3s-dev-1/2/3 at 192.168.1.50/.51/.52 — 6 vCPU, 24 GiB, Debian 13, k3s v1.36.4 |
| kube-API | kube-vip VIP 192.168.1.49:6443, reached from the workstation via NAT 192.168.2.50:6443 |
| Node SSH | pfSense NAT 192.168.2.102:2250/2251/2252 → node :22 (Ansible only) |
| Ingress VIP | 192.168.1.53 (Cilium L2, shared Gateway); .53–.60 reserved for LB VIPs |
The earlier libvirt/KVM cluster on 10.73.0.0/24 is retired. Any doc or command referencing
virsh, qemu:///system, or 10.73.0.x for the cluster is historical.